EXTRACTED TEXT FROM: 1940户外防水蜂眼摇头染色灯英文说明书.doc



1940 Outdoor Waterproof Bee Eye Shake Head Dyeing Light
user's guide




                           














Please read over this manual before operation the light




Thank you for choosing to use our 1915 Bee's Eye light. For the correct and safe use of this product, please read the instructions carefully before installing and using this product. This specification contains important installation and application information, please strictly follow the instructions when installing and operating the product. At the same time, please keep this instruction manual properly.
Our 1915 Bee's Eye light uses a new and beautiful high-temperature resistant metal body. This product is designed and produced in strict accordance with CE standards, in line with the international standard DMX512 signal protocol, can be used alone for control, can also be used online, with fast rotation, low noise, powerful features, suitable for small and medium-sized concerts, theaters, studios, nightclubs and bars and other places.
Please remove the package carefully, check whether the product is damaged during transportation, and check whether the following contents are complete.
1915 Bee's Eye light- - - - - - - - -1        instruction manual- - - - - - - - -1 book
Power line- - - - - - - -1,                  signal line- - - - - - - -1      

This product is a good product before delivery. In order to keep the product in good condition and ensure safe operation, users should follow the safety matters and the instructions.
Important: Damage caused by not following this instruction is not covered by the warranty. The supplier is not responsible for the product problems arising from this.
If the product has been exposed to extreme unstable temperature conditions (e. g., after transportation), do not supply the product immediately because water drops due to temperature changes may damage the product. Please use the product has returned to normal temperature.
This product can be used in the voltage range of 90-240V, and is used for indoor products. Please ensure that the ground voltage is not higher than the tolerable range of the product!! The power plug must be plugged into a protective class I socket. Green or tea-cyan conductors must be grounded.

Linkage of the DMX512 signal
This lamp uses DMX512 signal control mode, and the control signal of each lamp is in parallel. When connecting the signals of multiple lamps, it is best to use dual-core shielding cable. When connecting, each lamp is connected through the DMX signal jack (Canon seat) INPUT (input) and OUTPUT (output). The 3-core XLR plug terminal of the signal line connecting the lamp must correspond to each other. When connecting the lamp signal, it is recommended to use the DMX signal terminal. To damaging the control signal due to electrical noise, the DMX signal terminal is a 120 ohm 1W resistance between the 2 and three feet of an XLR plug and connects it to the OUTPUT (output) jack of the last lamp.
Calculation method of lamp starting address code:
The starting address code of the current lamp is equal to (the starting address code of the previous lamp) + (number of channels of the lamp) description:
1: Start address code value of the first lamp A001.
2: The basic number of controller should be greater than or equal to the total number of lighting channels.
3: Note: when any controller is used, each lamp must have its own starting address code. If the starting address code of the first lamp is set A001, the pass number of the lamp is 16 CH; then the starting address code of the second lamp is set to A017; the starting address code of the third lamp is set to A033; and so on, (this setting mode should be determined by different console).

Instructions for lamp installation
This lamp can be placed horizontally, oblique hanging and upside down, oblique hanging and upside down must pay attention to the installation method. Fixed installation of lamps: before the positioning of lamps, ensure the stability of the installation site, the lamps must not fall off the support frame, and use the support frame and the safety rope for auxiliary hanging; to ensure safety. Prevent the falling and sliding of the lamps and lanterns. During the installation and debugging, the pedestrians are prohibited to pass below, and regularly check whether the safety rope is worn and the hook screw is loose. If the installation of the lamp is not stable, the manufacturer will not bear any responsibility.


● Menu instructions
  primary menu Sublevel menu Three-level menu / parametersAddress001 - 512(Number of channels added each time, minus normal)System SettingsRun  modeDMX /Sound / Auto1/Auto2Channel  mode21CH/ 21+RGB CH/ 21+RGBW CH
23 CH/23+RGBW CH
35CH/35+RGB CHInvert  panOFF/ ONInvert  tiltOFF/ ONHall  crctOFF/ ONEncoder  crctOFF/ ONSignal  keepOFF/ ONScreen  saverOFF/ ONInvert  screenAuto/off/onUpdate  slaveOFF/ ONLanguageChinese/ENLoad  defaultOK/cancelManual mode Current channel mode channel0-255System calibration  enter passwordLighting calibrationSystem reset Reset effectReset scanReset allSystem information(Note) Reset the error messageDisplay the reset error messageAnd DMX data monitoringChannel values for the receiving console Sensor information Hall informationX-light coupling informationY light coupling informationHardware versionDisplays the hardware versionSoftware versionDisplays the software version

Screen automatic rotation function
The system can automatically rotate the screen according to the direction of gravity, without manual rotation. You can also turn off the automatic rotation function.

Manual control 
This interface is used to control the current lamps.
Press OK to enter the edit state. Press Up and Down to change the channel value. Press OK again to save the modified value, exit editing, and press Exit not to save the modified value, and directly exit editing.




 System calibration 
option illustrateInitial positionAfter entering the sub-interface, the initial position of the X-axis, Y-axis, focusing ,Rotate motor can be adjusted. The adjustment range of 0~255,127 means that there is no adjustment.White balanceAfter entering the sub-interface, the white balance of the lamp’s red、green、blue、white can be adjusted. The adjustment range of 0~255,255 means that there is no adjustment.PowerAfter entering the sub-interface,the power of the lamp bead can be adjusted. 255 indicates the maximum power.Other calibrationVoice-control sensitivity calibration, password modification.

Reset
Press Up and Down to switch the reset mode, and press OK to reset directly.
option instructionReset effectEffect motor reset except for XYReset scanXY axis reductionReset allLamps reset






System information 
option instructionReset informationIf the red ERR indicator shines, the lamp is running wrong, and details can be viewed in the subinterfaceAnd DMX data monitoringThis enters the subinterface to display channel values for viewingSensor information Real-time monitoring of the light coupling, hall and other sensors on the lamp stateHardware version numberLighting hardware informationSoftware version numberLamp software version
























●Channel mode
CH22CH36CH79CH98functionDMX valuesdescribe1111red0-255Linear dimming of red from dark to bright2222Red fine-tuning0-255Red fine-tuning
3333green0-255Linear dimming of green from dark to bright4444Green fine-tuning0-255Green fine-tuning5555blue0-255Linear dimming of blue from dark to bright6666Blue fine-tuning0-255Blue fine-tuning7777white0-255Linear dimming of white from dark to bright8888White fine-tuning0-255White fine-tuning9999Color temperature adjustment0-255Linear color temperature adjustment10101010Color Macro0-255Built in color gradient11111111Strobing0-3 HYPERLINK "file:///C:/Users/Admin/AppData/Local/Programs/baidu-translate-client/resources/app.asar/app.html" \l "/#" turn off the light4-103Synchronize strobe speed from slow to fast（1HZ-25HZ）104-107Lighting108-207Divide the strobe speed equally from slow to fast（1HZ-25HZ）208-212Lighting213-225Low speed random flashing226-238Medium speed random strobe239-251High speed random flashing252-255Lighting12121212Total dimming0-255Linear dimming from dark to bright13131313Total dimming fine adjustment0-255Overall dimming fine adjustment control14141414x-axis0-255Horizontal control15151515X-axis fine-tuning0-255Horizontal fine-tuning control16161616Y-axis0-255VERTICAL17171717Y-axis fine-tuning0-255Vertical fine-tuning control18181818macro0-255reserve19191919reset0-25NO FUNCTION26-76Lamp head reset effective for 5 seconds77-127XY reset valid for 5 seconds128-255All resets valid for 5 seconds20202020focus0-255focus21212121polygon mirror0-1270-60 degrees128-188Turning counterclockwise from fast to slow endlessly189-193cease194-255Clockwise rotation from slow to fast22362222frequency0-255Lamp bead frequency (1-10K)/23//Built in effects
(Matching effect color)
0-7not have8Static Effect 19Static Effect 210Static Effect 311not have12Static Effect 413Static Effect 514not have15Dynamic effects 116Dynamic effects 217Dynamic effects 318Dynamic effects 419Monochromatic random20Full color random21Rainbow Effect 122Rainbow Effect 223Dynamic effects 524Dynamic effects 625Dynamic effects 726Dynamic effects 827Dynamic effects 928Dynamic effects 1029Dynamic effects 1130Dynamic effects 1231Dynamic effects 1332Dynamic effects 1433not have34not have35Dynamic effects 1536Dynamic effects 1637Dynamic effects 1738Dynamic effects 1839Dynamic effects 1940Dynamic effects 2041not have42Dynamic effects 2143not have44Dynamic effects 2245Dynamic effects 2346Dynamic effects 2447Dynamic effects 2548Dynamic effects 2649Dynamic effects 2750Dynamic effects 2851Dynamic effects 2952Dynamic effects 3053Dynamic effects 3154Dynamic effects 3255Dynamic effects 3356Dynamic effects 3457Dynamic effects 3558Dynamic effects 3659Dynamic effects 3760Dynamic effects 3861Random location 162Random location 263Random location 364not have65Random location 466Random location 567Dynamic effects 3968Dynamic effects 4069not have70Dynamic effects 4171-255not have23Effect speed0-63Static effect64-158Forward from fast to slow159-160stillness161-255Reverse from slow to fast24Fade effect0-255Dynamic effect fading25Effect Red0-255Dynamic effect red26Effect Green0-255Dynamic effect green27Effect Blue0-255Dynamic effect blue28Effect white0-255Dynamic effect white29Effect Dimming0-255Pattern 0-100% Dimming30Background dimming0-255Background 0-100% dimming31Effect transition0-255Pattern change control32Effect supplementation0-255Pattern translation33Foreground flicker0-255Foreground strobe (same as channel 11)34Background strobe0-255Background strobe (same as channel 11)35background selection0-255background selection/2323R1 LED dimming0-255R1 LED dimming2424G1 LED dimming0-255G1 LED dimming2525B1 LED dimming0-255B1 LED dimming26W1LED dimming0-255W1 LED dimmingR2 LED dimming0-255R1 LED dimming……0-255……7795R19 LED dimming0-255R19 LED dimming7896G19 LED dimming0-255G19 LED dimming7997B19 LED dimming0-255B19 LED dimming/98W19 LED dimming0-255W19 LED dimming
8. Product maintenance and cleaning
Please note the following points when testing this product:
1. All screws and components for installing products must be tightly connected and not rusted.
2. The shell, lens, fixing parts, and installation location (such as ceiling, hanger, truss, etc.) must not be deformed.
3. Mechanical moving parts must not have wear and cannot rotate unevenly.
4. The power cord must not have any damage, material damage or scratches.
The installation and use of the product must be carried out by trained professional technical personnel, ensuring the elimination of safety hazards.


To maintain the good condition of the product and extend its service life, we recommend routine cleaning of the product.
1. Clean the external and internal lenses of the product every week to prevent reduced light output due to lens dust accumulation.
2. Clean the fan every week.
3. Every three months, a professional electrical engineer conducts a detailed circuit inspection of the product to ensure that the circuit contacts are in good condition to prevent aging caused by overheating.
We suggest regularly cleaning the product, please be careful not to use damp or burlap, and never use alcohol or solvents for cleaning.
This product is not equipped with replacement parts, please refer to the "Installation Instructions" section.
If the user needs any spare parts, please purchase from the local dealer.





























