EXTRACTED TEXT FROM: 全域防护420防水棱镜王（英文）说明书.docx

All-round Protection 420W Waterproof Prism King






Manual - Instruction 






Read the instructions carefully before use
Catalogue
1. Precautions and installation
1
1.1 Declaration
1
1.2 Maintenance
1
1.3 Product precautions
1
1.4 Product Introduction
1
1.5 Connecting Signal Cables
2
1.6 Lighting Installation
2
2. Control panel
4
2.1 Key Instructions
4
2.2 Main Menu
5
2.2.1 Settings
5
2.2.2 Manual
5
2.2.3 Information
6
2.2.4 Factory
7
3. Channel function
8
3.1
 Channel Table
8
4. Common Faults
 11


1. Precautions and installation Precautions and installation
Declaration
Thank you for choosing our products! 8, This product is in good condition and the package is complete when it leaves the factory. For your safe and effective use of this product, before you use this product, please read this manual carefully and completely. This manual contains important information for installation and use. Please install and operate according to the requirements of the manual. At the same time, please keep this manual properly for use at any time. Our company does not assume all responsibility for damage to lamps or other performance due to individuals not operating in accordance with the instructions during installation, use and maintenance.
This manual is subject to technical changes without prior notice.

Maintenance
Disconnect the power supply before performing maintenance.
This lamp should be kept dry and avoid working in wet environment.
Intermittent use will effectively extend the life of the luminaire.
In order to obtain good ventilation and lighting effects, pay attention to cleaning the fan and fan net as well as the lens often.
Do not rub the luminaires housing with organic solvents such as alcohol to avoid damage.

Product precautions
This light fixture is for professional use only.
Ensure that the power supply voltage matches the required power supply voltage of the equipment before operation.
Do not place this product in a place that is easy to loose or shake.
During use, if the lamp is abnormal, stop using the lamp in time.
In order to ensure the service life of the product, this product should not be placed in a humid or leaking place, and should not work in an environment where the temperature exceeds 60 degrees.
When the lamp is used, the power supply voltage change should not exceed ±10%, the voltage is too high, will shorten the life of the lamp, the voltage is too low, it will affect the light color of the lamp.
After the power off, it takes 20 minutes to use the lamp to cool down fully before it can be used again.
The rotating parts of the lamp and the attaching accessories must be checked regularly, and the loosening and shaking should be reinforced in time to prevent accidents.
In order to ensure the normal use of this product, please read this instruction carefully.

Product Description
Features & Technical Parameters
Features
• Fixture Material: Adopts high-end national standard die-cast aluminum shell—no plastic parts at all. Suitable for use in harsh outdoor environments such as heavy rainfall, high altitude, strong sandstorms, seaside, extreme cold and extreme heat.
• Waterproof Grade: Withstands 360° all-round huge wave impact, truly achieving IP65 waterproof rating.
• The waterproof beam light meets high industry standards in optics, structure, appearance and other performances. It adopts advanced technology, high-brightness light source, optical technology and rigorous industrial design to ensure the perfect presentation of lighting effects.
Technical Parameters
• Latest Mainboard Program: Supports RDM function; programmable built-in programs include multiple effect programs, enabling single white beam slow left-right swing, single color-changing beam slow left-right swing and multi-color-changing beams slow left-right swing.
• Voltage: Wide voltage 110V-240V, 50-60Hz
• Bulb Brand: Osram 371+ long-life light source
• Output Power: 480W
• Color Wheel: 15 colors + 7-color rainbow effect + atomization function
• Gobo Wheel: 14 fixed gobos
• Zoom: Electronic linear high-definition dynamic zoom, equipped with high-density glass optical lens
• Linear Dimming Curve: 0%-100% linear dimming
• Beam Angle: 1.8°
• Channels: 24 international standard DMX512 channels
• XY Motors: Three-phase electric drive, powerful, faster, more stable and quieter
• Control Modes: DMX 512, RDM, Auto-run, Master-Slave Auto-run
• Prisms: 8-prism / 8+16 prisms superimposed, rotatable with macro functions
• Display Screen: LCD screen adaptable to different installation positions
• Horizontal/Vertical Scanning: Capable of 540° horizontal or 270° vertical scanning with fast and stable speed
• Intelligent Photoelectric Reset Correction System: Automatically returns to the original position in case of accidental misoperation; equipped with horizontal and vertical locking knobs for easier maintenance and transportation
• Fixture Dimensions: 329228603mm
• Net Weight: 19.8KG
• Package Dimensions: 645490420mm
• Gross Weight: 24KG

Signal cable connection
Light fixtures feature standard DMX input and output 3-core or 5-core XLR sockets. Use a twisted-pair signal cable shielded specifically for DMX 512; The signal line is generally connected at a distance of 150 meters, and the DMX512 signal amplifier must be added for long distance signal transmission.
Use a shielded twisted-pair signal line from the DMX outlet of the controller to the DMX input of the first device, and from the DMX outlet of the first device to the DMX input of the second device, and so on, until all the lamps are connected. Then install a terminal plug on the last 3-pin connector of the connecting luminaire output on each line. (Weld a 4/1W, 120Ω resistor between the 2 and 3 pins of the 3-pin pin cannon plug).

Important: The wires should not touch each other or the metal housing.


Figure 1 Schematic diagram of DMX signal wire connection
The calculation method of the starting address code of the lamp:
The initial address code of the current luminaire is equal to (the initial address code of the previous luminaire)+(the number of channels of the luminaire)
1: The initial address code value of the first luminaire A001.
2: The basic channel number of the controller should be greater than or equal to the total number of channels used by the luminaire.
3: Note: when using any controller, each luminaire should have its own starting address code, if the first luminaire's starting address code is set A001, the number of luminaire channels is 16CH; Then the starting address code of the second lamp is set to A017; The starting address code of the third lamp is set to A033; And so on,(this setting also needs to be determined according to different consoles)

Luminaire installation
Luminaires can be placed horizontally, hung diagonally, and hung upside down. Be sure to pay attention to the installation method when hanging diagonally and upside down. 
As shown in Figure 2, before positioning the luminaire, it is necessary to ensure the stability of the installation site. During the reverse hanging installation, it is necessary to ensure that the luminaire does not fall down on the support frame. It is necessary to use the safety rope to pass through the support frame and the luminaire handle for auxiliary hanging to ensure safety. Prevent the luminaire from falling and sliding.
During the installation and commissioning of the lamp, pedestrians are prohibited from passing under the lamp, and the safety rope is regularly checked for wear and whether the hook screws are loose.
If the hanging installation is not stable, resulting in the fall of the lamp and all the consequences, our company does not assume any responsibility.

Figure 2 Schematic diagram of the lamp hanging upside down
Control panel

2.1 Key Instructions


Figure 3 Schematic diagram of key description on the panel
The following takes "Modify DMX address code" as an example to describe the use of keys:
1, if the current is not the main interface, press the "left" key (one or more times) to return to the main interface
2, in the home screen, press the "up" key or "down" key to select the "Settings" button
3. Press the "OK" key to enter the "Settings" interface
4, in the "Settings" interface, press the "up" key or "down" key to select "DMX address"
5, press the "OK" key to enter the editing state
6, press the "up" key or "down" key to modify the DMX address code
7, press the "OK" key to exit the editing state
2 Menu Description
      

Figure 4 Schematic diagram of main menu
2.2.1 Settings
Options
Instructions
Run
DMX
Slave state: Receives DMX signals from the console or host

Bootstrap
Host status: Self-drive and send DMX signal to slave

Voice Control

Scene setting


DMX address
1-512
Press "OK" to enter the editing state. At this time, the hundreds digit is selected, and press the "up" and "down" keys to change the address code. Press the "OK" key again to select the tens edit. Press "OK" again to select the ones edit. Press again to exit the editing state
Bulb
Off
Off Bubble

On
Bright Bubble
Motor reset

Off


On
Light fixture reset
Channel

Standard 16CH
Standard 16 channel mode

Extended 24CH
Expand 24 channel mode
Language
English
Set to English interface

Chinese
Set to the Chinese interface
Screen flip

Off
Front display

On
Screen inverted display
X Inversion

Off


On
X Motor direction rotation 540 degrees
Y reversal

Off


On
Y Turn the motor 270 degrees in the direction
XY switching

Off


On
Channel for switching XY axes (including fine tuning)
XY encoder

On
Use an encoder (optocoupler) to judge out of step and automatically correct the position

Off
Correct position without using an encoder (optocoupler)
DMX signal

Hold
Continue running in its original state

Reset
Turn the motor back and stop running
Turn on bright bubble
Off


On
Bright bubble after turning on
Linear color

On
The color wheel changes linearly

Off
Color wheel nonlinear change, half-color change
Clear scene data

Press the "OK" key to clear scene data
Restore default
On


Off
Press "OK" to see the confirmation dialog box, press "OK" again to restore the default Settings

Scene Setup Instructions
Options
Instructions
Scene selection
01-20
Select Scenario 1- Scenario 20 for programming
Scene time
0-255.
Set the running time of the current scene, up to 255 seconds
Scene Run
On
The default is on, which will be executed during auto run, and if it is set to interrupt, it will skip the current scene and run the next scene

Off

Step 1: Color
0-255.
Set console values 0-255
2 Cut light/strobe
0-255.

3 Dimmer
0-255.

4 Pattern plates
0-255.

5...
0-255.

6...
0-255.

2.2.2 Manual control
This interface is used to control the current luminaire (does not receive DMX signals), corresponding to the channel. Refer to the channel table for details
Options
Instructions
1CH.
0 ~ 255
Press "OK" to enter the editing state. At this time, the hundreds digit is selected, and press the "up" and "down" keys to change the channel value. Press the "OK" key again to select the tens edit. Press "OK" again to select the ones edit. Press again to exit the editing state
...
0 ~ 255

15CH.
0 ~ 255

...
0 ~ 255



2.2.3 Information

Options
Instructions
Ver

Show software version
DIS

Display board software version
MT

Motor board software version
Time information
Time information Steps 1 Total brightening bubbles
2. Total use
Record the cumulative bright-bubble time
Record the lighting time
System error

If the red ERR indicator is bright, it indicates that the lamp is running incorrectly. You can go to the subinterface to view the details. After viewing, you can press the "Clear" button to clear the error record
Blower speed

Displays the current blower speed
Hall Status
0000
0 when magnetic is detected, 1 otherwise
The X-axis encodes the disk step value
0000
The number of steps should increase for forward travel and decrease for reverse travel. The number should be normal every time you reach the same point
The Y-axis encodes the disk step value
0000
The number of steps should increase for forward travel and decrease for reverse travel. The number should be normal every time you reach the same point
Permission Duration

9999 No encryption; Other values can be used with encryption

A. Error message description

Common Error Messages
Instructions
MT board connection failed
Motor board not responding. There is a problem with the serial communication line connecting the display board to the motor board, or there is a problem with the motor board.
X-axis reset failed
There is a problem with the X-axis photoelectric switch, or the X-axis motor or motor board
Y-axis reset failed
Y-axis photoelectric switch, or Y-axis motor or motor board problem
X-axis Hall error
X-axis Hall, or a problem with the motor board
Y-axis Hall error
Y-axis Hall, or a problem with the motor board
Color disk reset failed
Color disk Hall, or there is a problem with the color disk motor
The pattern plate failed to reset
Pattern plate Hall, or pattern plate motor has a problem
The focus reset failed
Focusing Hall, or a problem with the focusing motor
Bulb control failure
Failure to light or extinguish bubbles, lamplighter or bulb problem

2.2.4 Factory
Calibrate
Fan adjustment (test)
Fan regulation


Blower speed


Wind speed low off Bubble on/off

Data download
After changing the display board, download the calibration data of the original display board from the motor board

X
After entering the sub-interface, the reset position of the motor such as X axis and Y axis can be adjusted to make up for the error on the hardware installation. The adjustment range is -128~+127, and +0 indicates no adjustment.

Y


Colors


Gobo


Focus


Dimming


Prism 1 Zero


Prism 1 Stroke


Prism 2 Zero


Prism 2 Stroke


Frost white light


Frost stroke


Colorful mirror stroke


Zeroing
close


On, the data is restored to default values

X Hall
Off, X Hall report wrong off


On, X Hall reports the wrong off

Y Hall
Off, Y Hall reports wrong off


On, Y Hall reports an error

Half power
Off, no half power function


On, with half power function
Channel function
3.1
 Channel Table
Channels
24 channel mode
1
Color Wheel
2
Shutter
3
Dimming
4
Gobo
5
Prism 1
6
Prism 1 Rotation
7
Prism 2
8
Prism 2 Rotation
9
Focus
10
X
11
X Fine
12
Y
13
Y Fine
14
XY Speed
15
Frost /Colorful
16
Lamp& Reset
17
LED_Dimming
18
LED_Shutter
19
LED_Red
20
LED_Green
21
LED_Blue
22
LED_Color macro
23
LED_Scene
24
LED_Scene Speed


Channel parameter values (full version) :
channel 1
 definition
 figure
 describe

 [ CH1 ]
x-axis
 0-255
 0-540 degrees

 [ CH2 ]
X-axis fine-tuning
 0-255
 0-2degrees

 [ CH3 ]
 Y-axis
 0-255
 0-270degrees

 [ CH4 ]
Y-axis fine-tuning
 0-255
 0-1 degrees

 [ CH5 ]
 XY velocity
 0-255
 From fast to slow

 [ CH6 ]
 aiming
 0-255
 0-100%dimming

 [ CH7 ]
 stroboflash



 
 
 0-3
Deinking

 
 
 4-103
 Pulse stroboscopic effect from slow to fast

 
 
 104-107
switch

 
 
 108-207
Gradual flicker transition from slow to fast

 
 
 208-212
 switch

 
 
 213-251
Random strobe from slow to fast 

 
 
 252-255
 switch

 [ CH8 ]
atomization



 
 
 0-127
 not have

 
 
 128-255
atomization

 [ CH9 ]
 colour disk



 
 
 0-4
 white light

 
 
 5-9
 White light color 1

 
 
 10-14
Color 1

 
 
 15-19
 Color 1+Color 2

 
 
 20-24
 Color 2

 
 
 25-29
 Color 2+ Color 3

 
 
 30-34
  Color 3

 
 
 35-39
 Color 3+ Color 4

 
 
 40-44
Color 4

 
 
 45-49
Color 4+Color 5

 
 
 50-54
Color 5

 
 
 55-59
Color 5+Color 6

 
 
 60-64
 Color 6

 
 
 65-69
 Color 6+Color 7

 
 
 70-74
Color 7

 
 
 75-79
 Color 7+Color 8

 
 
 80-84
Color 8

 
 
 85-89
 Color 8+Color 9

 
 
 90-94
 Color 9

 
 
 95-99
 Color 9+Color 10

 
 
 100-104
Color 10

 
 
 105-109
 Color 10+Color 11

 
 
 110-114
 Color 11

 
 
 115-119
 Color 11+Color 12

 
 
 120-124
 Color 12

 
 
 125-129
 Color 12+Color 13

 
 
 130-134
 Color 13

 
 
 135-139
 Color 13+Color 14

 
 
 140-197
From fast to slow, in a continuous flow

 
 
 198-255
Reverse flow from slow to fast

 [ CH10 ]
Map Plate



 
 
 0-4
white light

 
 
 5-9
 Pattern 1

 
 
 10-14
Pattern 2

 
 
 15-19
 Pattern 3

 
 
 20-24
 Pattern 4

 
 
 25-29
 Pattern 5

 
 
 30-34
Pattern 6

 
 
 35-39
 Pattern 7

 
 
 40-44
 Pattern 8

 
 
 45-49
Pattern 9

 
 
 50-54
Pattern 10

 
 
 55-59
Pattern 11

 
 
 60-64
Pattern 12

 
 
 65-69
 Pattern 13

 
 
 70-125
Reverse flow from fast to slow

 
 
 126-130
 cease

 
 
 131-190
From slow to fast, like a flowing stream

 
 
 191-195
 Jitter pattern from slow to fast 1

 
 
 196-200
 Jitter pattern from slow to fast 2

 
 
 201-205
Jitter pattern from slow to fast 3

 
 
 206-210
Jitter pattern from slow to fast 4

 
 
 211-215
 Jitter pattern from slow to fast 5

 
 
 216-220
 Jitter pattern from slow to fast 6

 
 
 221-225
Jitter pattern from slow to fast 7

 
 
 226-230
 Jitter pattern from slow to fast 8

 
 
 231-235
 Jitter pattern from slow to fast 9

 
 
 236-240
Jitter pattern from slow to fast 10

 
 
 241-245
Jitter pattern from slow to fast 11

 
 
 246-250
Jitter pattern from slow to fast 12

 
 
 251-255
Jitter pattern from slow to fast 13

 [ CH11 ]
 Rainbow Mirror



 
 
 0-127
 not have

 
 
 128-255
 colorful

 [ CH12 ]
Prism 1



 
 
 0-63
not have

 
 
 64-127
 Insert Prism 1-1

 
 
 128-191
  Insert Prism 1-2

 
 
 192-255
 Insert Prism 1-3

[ CH13 ]
 Prism Rotation



 
 
 0-127
 0-360 degrees

 
 
 128-187
From fast to slow, in a continuous flow

 
 
 188-195
cease

 
 
 196-255
Reverse flow from slow to fast

 [ CH14 ]
 Prism 2



 
 
 0-63
 not have

 
 
 64-127
 Insert Prism 2-1

 
 
 128-191
 Insert Prism 2-2

 
 
 192-255
 Insert Prism 2-3

[ CH15 ]
Prism 2 Rotation



 
 
 0-127
 0-360 degrees

 
 
 128-187
From fast to slow, in a continuous flow

 
 
 188-195
cease

 
 
 196-255
Reverse flow from slow to fast

[ CH16 ]
 focus
 0-255
From far to near

[ CH17 ]
lamp bulb



 
 
 0-99
No feature available

 
 
 100-105
Turn off the light bulb in 6 seconds

 
 
 106-199
 No feature available

 
 
 200-205
Turn on the light bulb in 6 seconds

 
 
 206-255
  No feature available

[ CH18 ]
Reduction/Function



 
 
 0-209
  No feature available

 
 
 210-215
Reset the XY motor in 6 seconds

 
 
 216-219
 No feature available

 
 
 220-235
6-second reset effect motor

 
 
 236-239
 No feature available

 
 
 240-255
Reset the entire light in 6 seconds

[ CH19 ]
 Effect Dimming
 0-255
 

[ CH20 ]
 Stroboscopic Flash
 
 

 
 
 0-3
 opening the light

 
 
 4-255
Shake from slow to fast

[ CH21 ]
effect



 
 
 0-14
 not have

 
 
 15-255
Apply a different effect for every five values

[ CH22 ]
 Effect Speed



 
 
 0-127
 From fast to slow, in a continuous flow

 
 
 128-255
Reverse flow from slow to fast



Common fault
According to some common faults, the corresponding solutions are put forward. Any problems that cannot be solved should be dealt with by professionals. Disconnect the light fixture from the power supply before maintaining it.
The light bulb is not working
Check that the voltage that matches the light fixture is installed;
Check whether the lamp power supply connection or control switch is in poor contact;
Check whether the power supply is insufficient;
Check that the DMX512 controller is sending instructions.

The light fixture does not accept control from the console after normal reset
Check luminaire digital start address value and function options are correct;
Check whether the connection of the communication control line is correct, the communication line is too long or has been interrupted;
Check whether the control equipment is invalid, check whether the signal amplifier connected to the series is invalid;
Check whether the communication line is too long or other devices interfere with each other;
Optimize wiring, shorten the length of the control signal line, high-voltage and low-voltage lines separate wiring;
Add signal amplifiers;
Signal line using high quality shielded twisted pair wire;
Connect the signal terminal resistor (120 ohms) at the end of the lamp.

Luminaire does not start
Check that the power supply parameters are consistent with the luminaire;
Check the lamps in the long distance transportation process due to extrusion deformation, internal parts vibration, moisture and other reasons, resulting in poor contact
Or fall off.
Please check whether the internal wire integration connector of the lamp has fallen off and is loose.
Check whether the electronic components of the lamp (such as electronic transformer, PCB board, motor control board, etc.) are loose, short circuit and burned out.

When working, the action of the X axis or Y axis of the luminaire is abnormal
Check them one by one by following the previous step;
Check whether the transmission belt corresponding to the X and Y axis direction in the lamp falls off and breaks;
Check whether the data feedback receiver (optocoupler) corresponding to the X and Y directions in the lamp is damaged;
Restart and reset once.