EXTRACTED TEXT FROM: 六颗复古灯英文说明书.doc



6 retro lights
User Manual





Thank you for choosing to use our 6 retro lights. In order to use this product correctly and safely, please read the instructions carefully before installing and using this product. This manual contains important installation and application information, please strictly follow the instructions when installing and operating the product. Meanwhile, please keep this manual in a safe place.
      Our 6 retro lights use a new and beautiful high temperature resistant metal body. This product is designed and produced in strict accordance with CE standards and conforms to the international standard DMX512 signal protocol. It can be used for control alone or online. It is suitable for various types of concerts, theaters, studios, nightclubs and bars.
This product uses high-brightness and stable LED three-in-one light beads, 60W high-brightness integrated light beads. Please remove the packaging carefully, and after removing the packaging, check whether the product has been damaged during transportation, and check whether the following contents are complete.
                   
6 retro lights-------1 set          Instruction manual-------1 set
  
Power cable--------1 set          Signal cable--------1 set               
This product is in good condition before leaving the factory. In order to keep the product in good condition and ensure safe operation, users should follow the safety precautions and warnings in this manual.
Important: Damage caused by not following this instruction is not covered under warranty. The supplier is not responsible for product problems caused by this.
If the product has been exposed to extreme unstable temperature environment (such as after transportation), please do not connect the product to the power supply immediately, as water droplets due to temperature changes may damage the product. Please use it after the product has returned to normal temperature.
This product can be used in the voltage range of 90-240V and is an indoor product. Please make sure that the ground voltage used is not higher than the product can withstand! ! The power plug must be inserted into a protected Class I socket. The green or teal conductor must be grounded.
Connection of DMX512 signal:
This light uses the DMX512 signal control mode, and the control signals of each light are in a parallel relationship. When connecting the signals of multiple lights, it is best to use a double-core shielded cable. When connecting, each light is connected through the DMX signal jack (XLR Socket) INPUT (input) and OUTPUT (output) are connected, and the 3-pin XLR plug terminals of the signal line connected to the light must correspond to each other. When connecting the light signal, it is recommended to use a DMX signal terminator. It can be avoided, due to electric dryness The DMX signal terminator is to connect a 120 ohm 1W resistor between pins 2 and 3 of an XLR plug, and connect it to the OUTPUT (output) jack of the last fixture.
light start address code calculation method:
The starting address code of the current fixture is equal to (the starting address code of the previous fixture) + (the number of channels of the fixture) Description:
1: The starting address code value of the first light is A001.
2: The number of basic channels of the controller should be greater than or equal to the total number of channels used by the lights.
3: Note: When using any controller, each light must have its own starting address code, if the starting address code of the first light is set to A001, and the number of light channels is 8CH; The starting address code of the two lights is set to A009; the starting address code of the third light is set to A017; and so on, (this setting method also needs to be determined according to different consoles)

1. LED Display section:             
                           A. Function
                        B.Up               
C. Down                        
D. Enter   
A    B   C    D

Operation instructions: Press function key A to cycle through different functions, and press B or C key to modify its parameter values. Press D key to confirm.






LED display window function comparison table, (all functions can be selected and then confirmed by D key)
No.DisplayFunction description1A001Address code (001-512) B, C key plus or minus address code value2CH8Channel mode switch3-512/Auto/SounDMX-512 mode/self-propelled mode/voice control mode
Product parameters introduction:
Input power: AC90V-240V
Power frequency: 50/60Hz
Power: 420W
Heat dissipation method: metal heat conduction
Maximum operating ambient temperature: 45°C
Number of light beads: 6 high-brightness 60W light beads + 144 LED three-in-one light beads
light bead type: RGB three-in-one light bead + integrated light bead
Strobe: 1-25 times/second
Number of DMX control channels: 8CH+28CH
DMX connector: 3Pin XLR
Operation Mode: DMX/Auto/Voice Control
Display mode: LED digital tube








Channel  8CH+28CH
8CHNo.FunctionDMX ValueDescription1Dimming0-2550-100% Linear Dimming2Strobe
0-3No function4-255Synchronized strobe3  R0-255LED red dimming from dark to bright4  G0-255LED green dimming from dark to bright5  B0-255LED blue dimming from dark to bright6  W0-255LED white dimming from dark to bright7  macro function




0-9No function10-19Built-in Effects 120-29Built-in Effects 2…One effect per 10 counts240-249effect 24250-255effect 258  Macro function speed regulation0-63static64-159Forward running speed from fast to slow160-255Reverse running speed from slow to fast
28CHNo.FunctionDMX ValueDescription1Dimming0-2550-100% Linear Dimming2Strobe
0-3No function4-255Synchronized strobe3  R10-255LED1 red dimming from dark to bright4  G10-255LED1 green dimming from dark to bright5  B10-255LED1 blue dimming from dark to bright6  W10-255LED1 white dimming from dark to bright7  R20-255LED2 red dimming from dark to bright8  G20-255LED2 green dimming from dark to bright9  B20-255LED2 blue dimming from dark to bright10  W20-255LED2 white dimming from dark to bright11  R30-255LED3 red dimming from dark to bright12  G30-255LED3 green dimming from dark to bright13  B30-255LED3 blue dimming from dark to bright14  W30-255LED3 white dimming from dark to bright15  R40-255LED4 red dimming from dark to bright16  G40-255LED4 green dimming from dark to bright17  B40-255LED4 blue dimming from dark to bright18  W40-255LED4 white dimming from dark to bright19  R50-255LED5 red dimming from dark to bright20  G50-255LED5 green dimming from dark to bright21  B50-255LED5 blue dimming from dark to bright22  W50-255LED5 white dimming from dark to bright23  R60-255LED6 red dimming from dark to bright24  G60-255LED6 green dimming from dark to bright25  B60-255LED6 blue dimming from dark to bright26  W60-255LED6 white dimming from dark to bright27

Macro function

0-9No function10-19Built-in Effects 120-29Built-in Effects 2…One effect per 10 counts240-249effect 24250-255effect 2528  Macro function speed regulation0-63static64-159Forward running speed from fast to slow160-255Reverse running speed from slow to fast
