EXTRACTED TEXT FROM: 广久LED500W光束灯-说明书-英文.doc



LED500W Beam Lamp User Manual



















DMX Channel table
16CHChannelFunctionNumerical valueDescription1X-axis0-2550-540 degrees2Y-axis0-2550-270 degrees3X-axis fine-tuning0-255X-axis 16 bit4Y-axis fine-tuning0-255Y-axis 16 bit5XY speed0-255From fast to slow6stroboscopic
 0 - 3dimming4 - 55Ordinary strobe light56 - 66dimming67 - 118Slow on, fast off119 - 129dimming130 - 181Fast on, slow off182 - 192dimming193 - 244Lightning flicker245 - 255dimming7dimming0-2550-100% linear dimming8color palette
0 - 9white light10 - 19White light+color 120 - 29Color 130 - 39Color 1+Color 240 - 49Color 250 - 59Color 2+Color 360 - 69Color 370 - 79Color 3+Color 480 - 89Color 490 - 99Color 4+Color 5100 - 109Color 5110 - 119Color 5+Color 6120 - 129Color 6130 - 139Color 6+Color 7140 - 149Color 7150 - 159Color 7+Color 8160 - 169Color 8170 - 210Clockwise rotation from slow to fast211 - 214white light215 - 255Rotate counterclockwise from slow to fast9CTO0 - 25510Fixed diagram
0 - 4round hole5 - 9Pattern 110 - 14Pattern 215 - 19Pattern 320 - 24Pattern 425 - 29Pattern 530 - 34Pattern 635 - 39Pattern 740 - 44Pattern 845 - 49Pattern 950 - 54Pattern 1055 - 59Pattern 1160 - 64Pattern 1265 - 69Pattern 1370 - 74Pattern 1475 - 79Pattern 1580 - 127Clockwise rotation from slow to fast128 - 132round hole133 - 180Rotate counterclockwise from slow to fast181 - 185Pattern 1 Shake186 - 190Pattern 2 Shake191 - 195Pattern 3 Shake196 - 200Pattern 4 Shake201 - 205Pattern 5 Shake206 - 210Pattern 6 Shake211 - 215Pattern 7 Shake216 - 220Pattern 8 Shake221 - 225Pattern 9 Shake226 - 230Pattern 10 Shake231 - 235Pattern 11 Shake236 - 240Pattern 12 jitter241 - 245Pattern 13 Shake246 - 250Pattern 14 shaking251 - 255Pattern 15 Shake11Prism 1&Prism 2
0 - 31no effect32 - 63Cut in Prism 164 - 127Cut in Prism 2128 - 255Prism 1&Prism 212Prism 1 rotation0 - 127Linear rotation128 - 191Clockwise rotation from slow to fast192 - 255Rotate counterclockwise from slow to fast13Prism 2 rotation
0 - 127Linear rotation128 - 191Clockwise rotation from slow to fast192 - 255Rotate counterclockwise from slow to fast14Atomization&Colorful0 - 127no effect128 - 192Cut into atomization193 - 255Cut into Rainbow15focusing0-2550-100% linear focusing16reset0 - 25no effect26 - 76Small motor reset77 - 127XY motor reset128 - 255Reset all motors

 Display board function operation
MENU : Cycle through the top menu or return to the previous menu
ENTER: Enter the next menu or confirm and save the selected parameters
UP: Up the menu, switch the selected parameter or increase the value
DOWN: Down the menu, switch the selected parameter or decrease the value
Menu structure
Set upFunctionAddress code1 - 512Set address codepassageway16CHSet channelOperating modeDMX512/go one's own way/Voice control/ManualSet operation modeAddress,code AutoOpen/shutThe address code is automatically calculated. For example, the current address code is 1 and the channel mode is 16CH. After the address code is turned on automatically, press the set address code to automatically add 16, that is, the address code becomes 17Signal holdopen/shutAfter opening, the original action will be maintained if there is no signalXYexchangeopen/shutX and Y channel exchangeX-axis reversalopen/shutX-axis reversalY-axis reversalopen/shutY-axis reversalEncoder error correctionopen/shutEncoder error correctionHall error correctionopen/shutHall error correctionRestore settingsYes / noRestore factory settings (but do not restore trim data)
Channel ManualFunction01X-axis0-25502Y-axis0-25503X-axis fine-tuning0-25504Y-axis fine-tuning0-25505XY speed0-25506stroboscopic0-25507dimming0-25508color palette0-25509CTO0-25510Fixed diagram0-25511Prism 1&Prism 20-25512Prism 1 rotation0-25513Prism 2 rotation0-25514Atomization&Colorful0-25515focusing0-25516reset0-255
CalibrationEffectPlease enter a 4-digit password to use this function
DisplayEffectScreen saver time15 seconds /30 seconds /60 seconds / offWhen the time arrives, return to the desktopbacklight time15 seconds /30 seconds /60 seconds / offThe screen will be off when the time reachesScreen reversalOn / offScreen forward and reverse controllanguageChinese / EnglishSelect Chinese or English
ResetEffectreset allYes / noReset all motorsXY resetYes / noXY motor resetHead reductionYes / noHead small motor reset	
Bulb settingffectPower on bright bubbleYes / noAutomatic bubble lighting after power on resetManual light bubbleYes / noManual bubblingHalf powerYes / noWhether half power mode is turned on
DMX data monitoringEffectMonitor DMX512 data value of each channel
Reset informationEffectIf the system reset is normal, the system is normal. If there is a reset error, the corresponding reset error message will be prompted
Sensor informationEffectX encoder*****Current encoder count valueY encoder*****Current encoder count valueX encoder status00/11Encoder a and B signal line statusY encoder status00/11Encoder a and B signal line statusX Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Y Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Color disc Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Pattern disc Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Focusing Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0
Usage recordEffectUse times, use time, bright bubble time, etc
System versionEffectSystem hardware version, software version number
Explain：
1. when restoring factory settings, only the underlined parameters in the menu will be restored, and other parameters will not be automatically restored or reset.
【Send local parameters】 menu, you can send the parameter settings of underlined items in the machine to another lamp or multiple lamps through DMX data line to avoid repeated setting work. A reset will be generated when the received lamps receive the correct parameters.
Troubleshooting
ResolventThe lamp is not powered on and has no response at allCheck the fuse for damage
 check whether the AC voltage is normal
Switching power supply inside the lamp body may be damaged
 the internal control board of the lamp body may be damaged
Uncontrolled lamps check whether the DMX signal is normal. When it is normal, the DMX signal indicator on the display board will flash
 check whether the address code is set correctly
 check whether the channel mode is set correctly
Check whether the DMX signal line is too long, or whether there are too many lamps connected in seriesAbnormal movement of XY axisThe optocoupler sensor may be damaged or improperly installed, so that the original correct position can also be corrected. Set it to no in the menu [XY error correction enable] option. Or adjust the optocoupler sensor circuit board to the appropriate position, or replace the circuit board







