EXTRACTED TEXT FROM: 耀眼460W三合一说明书(英文版).docx

Pattern lamp

Use to tell the book



Read the instructions carefully before useRead the instructions carefully before use
Read the instructions carefully before use

Read the instructions carefully before use

Catalogue
1. Precautions and installation1
1.1 Statement1
1.2 Maintenance1
1.3 Product Precautions1
1.4 Product Introduction1
1.5 Signal Cable connection2
1.6 Lamp Installation3
2 Control Panel4
2.1 Keystroke Instructions4
2.2 Main Menu5
2.2.1 Settings6
3 Channel functions7
3.1Channel table7
4 Common faults11


Precautions and installation Precautions and installation
Statement
Thank you for choosing our products!734 This product is in good condition and the package is complete when it leaves the factory.For your safe and effective use of this product, please read this instruction carefully and completely before you use this product.This instruction manual contains important information for installation and use. Please install and operate in accordance with the instructions. At the same time, please keep this instruction manual properly for use at any time.Our company does not assume all responsibility for damage to luminaires or other performance due to individuals not following the instructions during installation, use or maintenance.
This manual is subject to technical changes without prior notice.

Maintenance
Disconnect the power supply before performing maintenance.
The lamp should be kept dry and avoid working in wet environment.
Intermittent use will effectively extend the life of the luminaire.
For good ventilation and lighting, take care to clean the fan and fan net as well as the lens frequently.
Do not rub the light fixture housing with organic solvents such as alcohol to avoid damage.

Product Precautions
This light fixture is for professional use only.
Ensure that the power supply voltage is consistent with the equipment requirements before running.
Do not place this product in a place that is easy to loosen or shake.
In the process of use, if the lamp appears abnormal, it should stop using the lamp in time.
In order to ensure the service life of the product, the product should not be placed in damp or leaking places, but also should not work in the environment where the temperature exceeds 60 degrees.
After power failure, it takes 20 minutes to use the lamp to cool down fully before power use again.
The rotating parts of the lamps and pasting accessories must be checked regularly. If they are loose and shake, they should be reinforced in time to prevent accidents.
In order to ensure the normal use of this product, please read the instructions carefully.

Product Introduction
Power of light source: 400W;
Voltage: AC 110V~220V/50~60Hz;
Color disk: Each disc consists of 8 disc white light;
Color system: independent CMY+CTO color mixing system.
Pattern plate: 12 patterns are made up of white circles;
Glass pattern: 7 patterns are made up of white circles;
540° translation, 270° tilt.
Overheat protection;
Control mode: DMX512/ master-slave/Automatic;
IP20 protection level

Signal cable connection
Light fixtures feature standard DMX input and output 3-core or 5-core XLR sockets.Use a shielded twisted-pair signal cable designed for DMX 512;The signal line is generally connected at 150 meters, and the DMX512 signal amplifier must be added for long distance signal transmission.
Connect a shielded twisted-pair signal line from the DMX outlet of the controller to the DMX input of the first device, and from the DMX outlet of the first device to the DMX input of the second device, and so on, until all lights have been connected. Then install a terminal plug on the last connected light outlet 3-core jack on each circuit.(Weld a 4/1W, 120Ω resistor between the 2 and 3 pins of the 3-core pin cannon plug).

Important: The wires should not touch each other or the metal housing.


Figure 1 Schematic diagram of DMX signal cable connection
Calculation method of starting address code of luminaire:
The initial address code of the current luminaire is equal to (the initial address code of the previous luminaire)+(the number of channels of the luminaire)
1: Start address code value A001 of the first luminaire.
2: The basic channel number of the controller, should be greater than or equal to the total number of channels used by the lamp.
3: Note: when using any controller, each lamp should have its own initial address code, if the initial address code of the first lamp is set A001, the number of lamp channel pass is 16CH;Then the start of the second lamp address code is set to A017;The initial address code of the third lamp is set to A033;And so on,(this setting also needs to be determined according to different control platforms)

Luminaire installation
Light fixtures can be placed horizontally, slanted, and hung upside down.Be sure to pay attention to the installation method when hanging diagonally and upside down.
As shown in Figure 2, before positioning the lamp, it is necessary to ensure the stability of the installation site. When installing the reverse hanging, it is necessary to ensure that the lamp does not fall down on the support frame. It is necessary to use the safety rope through the support frame and the lamp handle for auxiliary hanging to ensure safety. Prevent the luminaire from falling and sliding.
When installing and debugging the lamps, it is forbidden for pedestrians to pass under them. Regularly check whether the safety rope is worn and whether the hook screws are loose.
Our company does not assume any responsibility for all consequences caused by the fall of the lamp due to the unstable installation of the hanging.

Figure 2. Schematic diagram of the lamp hanging upside down
















Control panel

2.1 Key Instructions





Figure 3 Schematic diagram of key description on the panel
The following takes "Modify DMX address code" as an example to describe the use of keys:
1, if the current is not the main interface, press the "left" key (one or more times) to return to the main interface
2, in the main interface, press the "up" key or "down" key to select the "DMX Settings" button
3. Press the "OK" key to enter the "DMX Settings" interface
4, press the "up" key or "down" key to modify the DMX address code
5, press the "OK" key to exit the editing state
6. Press the right button on the main interface to enter the calibration interface shortcut key.
7. Note: The shortcut keys at the bottom of the main interface, Chinese/English, screen rollover and reset, can only be manually touched, not pressed.



  Figure the main menu diagram

2.2.1 DMX Settings
Key description: Press up or down is +1 or -1 mode;Press the right button is the next one;Press the left and confirm button to save and exit.
Manual instructions: Enter the hundreds place first, then the tens place, then the last place.(For example, to enter the 286 address code, click 2, then 8, and finally 6)
2.2.2 Menu
Main menu 
Secondary menu
Three-level menu
Four-level menu
Five-level menu

DMX Setup 
Dmx Address
1 - 512




Channel Mode 
24CH




Run Mode
DMX 





Auto 





Sound 



Personality
Pan Inverse 
No 





Yes




Tilt Inverse
No 





Yes




Tilt Feedback 
Off





On 




Dimmer Curve 
Linear 





Square Law 





Inv SQ Law 





S-Curve 




LED Frequency 
600Hz





1200Hz





2400Hz 





4800Hz 





9600Hz 





12000Hz 





24000Hz




No Data Mode
Blackout





Hold




M/S Mode 
Slave 





Master 




Sensitivity 
10 - 100



Display
Display Rotate 
Normal 





Rotate 180 




Display Intensity 
1-100




Temperature Unit
°C





°F




Language 
English





中文



Motor Reset 
All 
No





Yes




Tilt 
No 





Yes




Effect 
No 





Yes



Manual Control 
Pan 
0 - 255




。。。
0 - 255




Function 
0 - 255



DMX Live 
Pan 
0 - 255




。。。
0 - 255




Function
0 - 255



Service 
Password
Calibration 
Motor 
Pan 
-128 -> 127




。。。
-128 -> 127


Factory Default 
No 








Channel parameter values (full version) :

CHANNEL
NAME
VALUE
DERIF
1
Pan 
000-255
From 0% to 100%
2
PanFine 
000-255
From 0% to 100%
3
Tilt 
000-255
From 0% to 100%
4
TiltFine 
000-255
From 0% to 100%
5
PanTiltSpeed 
000-255
Horizontal and vertical speed, fast to slow
6
Frost 
000127
NULL


128255
Atomization cut-in
7
Dimmer
000-255
From 0% to 100%
8
DimmerFine 
000-255
From 0% to 100%
9
Strobe 
000-009
Open


010-199
Sync strobe slow to fast


200-249
Random strobe slow to fast


231-255
Open
10
CTO 
000-255
From 0% to 100%
11
Cyan
000-255
From 0% to 100%
12
Magenta
000-255
From 0% to 100%
13
Yellow 
000-255
From 0% to 100%
14
Colour
000-009
white


010-019
Colo1


020-029
Colo2


030-039
Colo3


040-049
Colo4


050-059
Colo5


060-069
Colo6


070-079
Colo7


080-089
Colo8


090099
white  + Colo1


100-109
Colo1 + Colo2


110-119
Colo2 + Colo3


120129
Colo3 + Colo4


130-139
Colo4 + Colo5


140-149
Colo5 + Colo6


150159
Colo6 + Colo7


160-169
Colo7 + Colo8


170-179
Colo8 + Colo9


180-215
Forward rotation is slow to fast


216-220
Stop 


221-255
The reversal is slow to fast
15
FixGobo
000-007
white 


008-015
GOBO 1


016-023
GOBO 2


024-031
GOBO 3


032-039
GOBO 4


040-047
GOBO 5


048-055
GOBO 6


056-063
GOBO 7


064-071
GOBO 8


072-079
GOBO 9


080-087
GOBO 10


088-095
GOBO 11


096-103
GOBO 1: Jitter from slow to fast


104-111
GOBO 2: Jitter from slow to fast


112-119
GOBO 3: Jitter from slow to fast


120-127
GOBO 4: Jitter from slow to fast


128-135
GOBO 5: Jitter from slow to fast


136-143
GOBO 6: Jitter from slow to fast


144-151
GOBO 7: Jitter from slow to fast


152-159
GOBO 8: Jitter from slow to fast


160-167
GOBO 9: Jitter from slow to fast


168-175
GOBO 10: Jitter from slow to fast


176-183
GOBO 11: Jitter from slow to fast


184-191
GOBO 12: Jitter from slow to fast


192-221
Forward rotation is slow to fast


222-225
Stop 


226-255
The reversal is slow to fast
16
RotGobo
000-009
white 


010-019
GOBO 1


020-029
GOBO 2


030-039
GOBO 3


040-049
GOBO 4


050-059
GOBO 5


060-069
GOBO 6


070-099
GOBO 7


100-109
GOBO 1: Jitter from slow to fast


110-119
GOBO 2: Jitter from slow to fast


120-129
GOBO 3: Jitter from slow to fast


130-139
GOBO 4: Jitter from slow to fast


140-149
GOBO 5: Jitter from slow to fast


150-159
GOBO 6: Jitter from slow to fast


160-189
GOBO 7: Jitter from slow to fast


190-221
Forward rotation is slow to fast


222-223
Stop


224-255
The reversal is slow to fast
17
GoboRot 
000-127
Pattern angle adjustment


128-190
The pattern is turning slower to faster


191-192
The pattern rotation stops


193-255
Pattern reversal is slow to fast
18
Focus
000-255
From 0% to 100%
19
Zoom 
000-255
From 0% to 100%
20
Prism1 
000-127
NULL


128-255
Prism 1 cuts in
21
Prism1Rot
000-063
Prism angle adjustment


064-126
The prism is turning slower to faster


127-128
The prism rotation stops


129-191
Prism reversal is slow to fast


192-255
The prism rotates and shakes
22
Prism2 
000-127
NULL


128-255
Prism 2 cuts in
23
Prism2Rot 
000-063
Prism angle adjustment


064-126
The prism is turning slower to faster


127-128
The prism rotation stops


129-191
Prism reversal is slow to fast


192-255
The prism rotates and shakes
24
Function 
230-235
The head motor is reset and held for 3S


240-245
XY reset, hold 3S


250-255
All motors are reset and held for 3S












Common faults
According to some common faults, the corresponding solutions are put forward.Any unsolvable problems should be dealt with by professionals.Disconnect the light fixture before maintaining it.

The lamp will not accept control from the console after normal reset
Check luminaire digital start address value and function options are correct;
Check whether the connection of communication control line is correct, the communication line is too long or has been interrupted;
Check whether the control equipment is invalid, check whether the serial access signal amplifier is invalid;
Check whether the communication line is too long or other equipment interferes with each other;
Optimize wiring, shorten the length of control signal lines, high voltage and low voltage lines separate wiring;
Add signal amplifiers;
Signal line using high-quality shielded twisted pair wire;
Connect the signal terminal resistor (120 ohm) at the end of the lamp.

Luminaire does not start
Check that the power supply parameters are consistent with the lamp;
Check the poor contact caused by extrusion deformation, vibration and moisture of internal parts in the long distance transportation process
Or fall off.
Please check whether the internal wire integration connector of the lamp has fallen off or loosened.
Check whether the electronic components of the lamp (such as electronic transformer, PCB board, motor control board, etc.) are loose, short circuit and burned out.

When working, the action of the X or Y axis of the lamp is not normal
Follow the previous step to check them one by one;
Check whether the transmission belt corresponding to the X and Y axis directions in the lamp falls off and breaks;
Check whether the data feedback receiver (optocoupler) corresponding to the X and Y directions in the lamp is damaged;
Restart the machine and reset it once.