EXTRACTED TEXT FROM: 英文户外防水面光摇头灯说明书.doc

Outdoor Waterproof Moving Head Fresnel Light




USER MANUAL
（TFT DISPLAY）

CONTENTS
 TOC \o "1-3" \h \z \u  HYPERLINK \l "_Toc143529119" Chapter 1 Installation and attention	 PAGEREF _Toc143529119 \h 1
 HYPERLINK \l "_Toc143529120" 1.	Maintenance	 PAGEREF _Toc143529120 \h 1
 HYPERLINK \l "_Toc143529121" 2.	Statement	 PAGEREF _Toc143529121 \h 1
 HYPERLINK \l "_Toc143529122" 3.	Safety Precaution	 PAGEREF _Toc143529122 \h 1
 HYPERLINK \l "_Toc143529123" 4.	Cable connection（DMX）	 PAGEREF _Toc143529123 \h 1
 HYPERLINK \l "_Toc143529124" 5.	Rigging (Optional)	 PAGEREF _Toc143529124 \h 2
 HYPERLINK \l "_Toc143529125" 6.	RDM Note	 PAGEREF _Toc143529125 \h 3
 HYPERLINK \l "_Toc143529126" Chapter 2  Panel operation	 PAGEREF _Toc143529126 \h 4
 HYPERLINK \l "_Toc143529127" 1.	Control instructions	 PAGEREF _Toc143529127 \h 4
 HYPERLINK \l "_Toc143529128" 2.	Interface Description	 PAGEREF _Toc143529128 \h 4
 HYPERLINK \l "_Toc143529129" 3.	Setting interface	 PAGEREF _Toc143529129 \h 4
 HYPERLINK \l "_Toc143529130" 4.	Information interface	 PAGEREF _Toc143529130 \h 5
 HYPERLINK \l "_Toc143529131" 5.	Customized interface	 PAGEREF _Toc143529131 \h 6
 HYPERLINK \l "_Toc143529132" 6.	Advanced interface	 PAGEREF _Toc143529132 \h 6
 HYPERLINK \l "_Toc143529133" Chapter 3  Channel description	 PAGEREF _Toc143529133 \h 7
 HYPERLINK \l "_Toc143529134" 1.	Channel table	 PAGEREF _Toc143529134 \h 7

Chapter 1 Installation and attention 
Maintenance
To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
Intermittently using will extend this item’s service life.
Please clear the fan, fan net, and optical lens in order to keep good work state.
Do not use the alcohol or any other organic solvent to wipe the shell.
Statement
The product has perfect performance and integrity packing. All users should be strictly complying with the warning and operating instructions as stated. Or we aren’t in charge of any result by misusing. Any damage resulting by misuse is not within the Company’s warranty. Any fault or problem caused by neglecting the manual is also not in the charge of dealers.
   Note: All information is subject to change without prior notice.
Safety Precaution
In order to guarantee the product’s life, please don’t put it in the damp places or even the environment over 60degress.
Always mount this unit in safe and stable matter.
Install or dismantle should operate by professional engineer.
Using lamp，the change rate of power voltage should be within±10%，If the voltage is too high，it will shorten the light’s life; If it’s not enough, will influence the effect.
Please restart it 20 minutes later after turning off light , until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.
In order to make sure the product is used well, please read the Manual carefully.
Cable connection（DMX）
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires  must not make contact with each  other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
Figure  SEQ 图_ \* ARABIC 1  DMX Cable connection
Rigging (Optional)
This equipment can be positioned and fixed by clamp in every direction of the stage. Locking system makes it easy to fasten to the bracket. 
Attention! Two clamps is needed to fix the equipment. Every clamp is locked by fastener of 1/4 kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary accessory can not hang on the delivery handle. Nip the equipment on bracket.
Check if rigging clamp (not including the one inside) damaged or not? If stand ten times weight as the equipment. Make sure the architecture can stand ten times weight as all the equipments, clamps, wirings and other additional fixtures.
Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to clamp bracket, and then screw the nuts.
Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the two levers by 1/4 rotating clockwise; then install another clamp.
Install on safety string which stands at least ten times weight as equipment. Terminal of the accessory is designed for clamps.
Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment to flammable material or lighting source.

Figure  SEQ 图_ \* ARABIC 2  Installation 
RDM Note
RDM is an extended version of DMX512-A protocol. It is a remote device management protocol. Traditional DMX512 protocol communication is one-way communication. The protocol is based on RS-485 bus. RS-485 is a time-sharing multi-point, half-duplex protocol. Only one port is allowed to output at the same time. So, when using RDM, we should pay attention to it. The following points:
To use console or host device that supports RDM host protocol.
Use bidirectional signal amplifier, traditional one-way signal amplifier is not suitable for RDM protocol, because the RMD protocol needs feedback data, the use of one-way amplifier will block the return of data, resulting in no search fixture;
All fixture must be set to DMX mode to ensure only one host on the cable.
A 120 ohm impedance matching resistor must be inserted between terminals 2 and 3 of the terminal plug. When the signal line is longer, reducing the signal reflection will make the differential signal more stable and beneficial to the quality of communication.
When the fixture appears to accept DMX control, but can not been search by RDM host, first check the signal amplifier, and then check whether the signal line 2, 3 lines have bad contact.
Chapter 2  Panel operation
Control instructions



The function of the 'return' button is to return to the previous interface and exit the function 
The function of the 'up' button is to select the previous item or increase the value by pressing for 2 seconds to quickly increase it 
The function of the "down" button is to select the next item or decrease the value by pressing 2 seconds to quickly decrease it 
The functions of the "OK" button are: confirm save, execute functions, start editing, and exit editing

Interface Description

Two LED indicators on the left
Green - (DMA signal indicator light)
Blue --- (constantly on (self running voice control of the host) flashing (error indication))
The three buttons in the upper right corner are used for language switching and screen rotation.
The sub interfaces corresponding to the four buttons in the bottom row are introduced below.

Setting interface  
   
optionillustratemodeDMXSlave state: receiving DMX signals from the control console or hostAUTOHost status: automatically running and sending a DMX signal to the slaveSoundHost status: Voice controlled operation and sending DMX signal to the slavesceneHost status: self programmed to run and send a DMX signal to the slaveDMX Address1~512Press the "OK" button to enter the editing status. The "up" and "down" keys change the address code. Press' OK 'again to exit editing statusChannel Mode1313CHX inversionOFFONY inversionOFFONX inversionOFFONSwap channels for the XY axis (including fine tuning)ResetSelect 'Yes' to confirm and initiate resetXY encoderONUsing an encoder (optocoupler) to determine out of step and automatically correct the positionOFFCorrection of position without encoder (optocoupler)NO DMX Signal KEEPNo signal, continue to maintain the original stateCLEARNo signal. The motor returns to its starting positionScreensaverONTurn off backlight after idle for 30 secondsOFFlights onColor linearSelect 'On' or 'Off' to enable or disable the color wheel linear functionIndicator modeMODE1Green with DMXs constantly on, blue with host status constantly onMODE2Green with DMXs constantly on, blue with host status constantly on, flashing with error messagesLoad DefaultSelect 'Yes' to confirm and restore the default settings
Information interface
optionillustrateVersionCurrent software versionTotal Fixaccumulated use timeFixture timeUsage time since this startupTotal LampAccumulated bright bubble timeLamp timeTotal bright bubble timeSensor StatusDisplay the temperature information of the optocoupler Hall fan motherboard
Customized interface
This interface is used for self programming and self running programs. When in the DMX mode, there is a DMX signal to view the current data and save the current state

When there is no DMX signal, the desired data can be manually set and saved 
optionillustrateRUN STEP1-16How many steps do I need to run in custom modeNOW STEP1-16What steps are currently in progressStop time1-99Set the current step running timeSaveSave the current state and proceed to the next stepPan0~255Press the "OK" button to enter the editing status. Press the "Up" and "Down" keys to change the channel value. Press the 'OK' button again to exit editing statusTilt0-255Pan Fine0-255Tilt Fine0-255……0~255Advanced interface

optionillustrateTime zeroClear the usage time of the bright bubble to zero RetimeChannel ModeMODE1
MODE2CalibrationAfter entering the sub interface, the reset positions of the X-axis, Y-axis, and other motors can be adjusted to compensate for hardware installation errors
Attention: Do not perform reset calibration while the motor is running! If the motor is running, please stop it before performing reset calibration
If necessary, please perform a reset operation before performing a reset calibrationChannel orderSelect the channel value to change the function
Multiple functions cannot select the same valueSystem ErrorsThe error message generated by resetting can be cleared by selecting error reset
Chapter 3  Channel description
Channel table
channelnamevaluedescribeCH1PAN0-2550-540°CH2PAN Fine0-2550-2.1°CH3TILT0-2550-270°CH4TILT Fine0-2550-1.0°CH5XY SPEED0-255fast to slowCH6DIMMER0-2550-100%CH7DIMMER Fine0-255CH8STROBE0-3
4-127
128-191
192-251
252--255Dark
Slow strobe to fast strobe
Pulse flicker slow fast
Random flicker slow fast
OpenCH9COLOR0
20
40
60
80
100
120
140-199
200-255White
White + Color 1
Color 1
Color 1+ Color 2
Color 2
Color 2+ Color 3
Color 3
Rotate forward (fast to slow)
Rotate reverse (slow to fast)CH10CTO0-9
10-255Color
CTO 0%-100%CH11FOCUS0-255far to nearCH12LED0-9
10-255None
Every 10 values have a slow fast effectCH13RESET0-25
26-76
77-127
128-255non-functional
Reset EFT over 5 seconds
Reset XY over 5 seconds
Reset ALL over 5 seconds

