EXTRACTED TEXT FROM: LED300W三合一-说明书-英文.doc

LED300Wthree-in-oneBeam Lamp User Manual
catalogue
 TOC \o "1-3" \h \z \u  HYPERLINK \l _Toc14038 1. Dimensional drawing	 PAGEREF _Toc14038 3
 HYPERLINK \l _Toc4460 2. Major function	 PAGEREF _Toc4460 3
 HYPERLINK \l _Toc25574 3. DMX Channel table	 PAGEREF _Toc25574 4
 HYPERLINK \l _Toc1074 4. Display board function operation	 PAGEREF _Toc1074 6
 HYPERLINK \l _Toc24787 5. Troubleshooting	 PAGEREF _Toc24787 8

1.Major Function
Input voltage: AC 100v-240v/47-63hz
Power waste： LED300 W
Bulb type：LED300W
Control mode: DMX512 control / built-in self-propelled / voice controlled self-propelled / master-slave
 Channel mode: 20 channels
 One color disc has 9 colors plus white light, and one pattern disc has 8 patterns plus white light. The color wheel has a flowing half color effect. The pattern disc has the effect of water rolling and shaking.
 One prisms with arbitrary angle positioning and positive and negative rotation effects respectively.
 The stroboscopic has multiple stroboscopic functions, and the gradual opening and closing light is smooth without jitter
Degree of protection： IP20
Size:   mm
Net weight: Kg
2.DMX Channel table
DMX Channel table
20CHChannelFunctionNumerical valueDescription1X-axis0 - 2550-540 degrees2X-axis fine-tuning0 - 255X-axis 16 bit3Y-axis0 - 2550-270 degrees4Y-axis fine-tuning0 - 255Y-axis 16 bit5XY speed0 - 255From fast to slow6dimming0 - 2550% -100% linear dimming7stroboscopic
0 - 3dimming4 - 55Ordinary strobe light56 - 66dimming67 - 118Slow on, fast off119 - 129dimming130 - 181Fast on, slow off182 - 192dimming193 - 244Lightning flicker245 - 255dimming8color palette
0 - 4white light5 - 9White light+color 110 - 14Color 115 - 19Color 1+Color 220 - 24color 225 - 29Color 2+Color 330 - 34color 335 - 39Color 3+Color 440 - 44Color 445 - 49Color 4+Color 550 - 54Color 555 - 59Color 5+Color 660 - 64Color 665 - 69Color 6+Color 770 - 74Color 775 - 79Color 7+Color 880 - 84Color 885 - 89Color 8+Color 990 - 94Color 995 - 99Color 9+White Light100 - 75Clockwise rotation from slow to fast176 - 179white light180 - 255Rotate counterclockwise from fast to slow9Fixed diagram disk
0 - 9round hole10 - 19Figure 120 - 29Figure 230 - 39Figure 340 - 49Figure 450 - 59Figure 560 - 69Figure 670 - 79Figure 780 - 89Figure 890 - 125Rotate counterclockwise from fast to slow126 - 129round hole130 - 265Clockwise rotation from slow to fast166 - 175Circular hole shaking176 - 185Graph 1 jitter186 - 195Graph 2 jitter196 - 205Figure 3 Shake206 - 215Figure 4 Shake216 - 225Figure 5 Shake226 - 235Figure 6 Shake236 - 245Graph 7 jitter246 - 255Graph 8 jitter10Effect pattern
0 - 9no effect10 - 127Linear flow128 - 255Slow to fast flowing water11Dynamic diagram disk
0 - 14Glass circular hole15 - 29Picture 130 - 44Picture 245 - 59Picture 360 - 74Picture 475 - 89Picture 590 - 104Picture 6105 - 119Botu 7120 - 129Glass image 1 shaking130 - 139Glass image 2 shaking140 - 149Glass diagram 3 shaking150 - 159Picture 4 jitter160 - 169Glass Figure 5 Shake170 - 179Glass chart 6 jitter180 - 189Glass diagram 7 shaking190 - 221Rotate counterclockwise from slow to fast222 - 223Glass circular hole224 - 255Clockwise rotation from fast to slow12Rotating motion diagram
0 - 127any position128 - 189Clockwise rotation from fast to slow190 - 193stop194 - 255Rotate counterclockwise from slow to fast13prism
0 - 127no effect128 - 255Cut into prism14Prism rotation
0 - 127Linear rotation128 - 187Clockwise rotation from fast to slow187 - 195stop196 - 255Rotate counterclockwise from slow to fast15Atomization&Colorful
0 - 127no effect128 - 192Cut into atomization193 - 255Cut into Rainbow16magnify0 - 2550% -100% linear amplification17focusing0 - 2550% -100% linear focusing18reset0 - 25no effect26 - 76Small motor reset77 - 127XY motor reset128 - 255Reset all motors19effect0 - 25520Effect speed0 - 255

 Display board function operation
MENU : Cycle through the top menu or return to the previous menu
ENTER: Enter the next menu or confirm and save the selected parameters
UP: Up the menu, switch the selected parameter or increase the value
DOWN: Down the menu, switch the selected parameter or decrease the value
Menu structure
Set upFunctionAddress code1 - 512Set address codepassageway16CHSet channelOperating modeDMX512/go one's own way/Voice control/ManualSet operation modeAddress,code AutoOpen/shutThe address code is automatically calculated. For example, the current address code is 1 and the channel mode is 16CH. After the address code is turned on automatically, press the set address code to automatically add 16, that is, the address code becomes 17Signal holdopen/shutAfter opening, the original action will be maintained if there is no signalXYexchangeopen/shutX and Y channel exchangeX-axis reversalopen/shutX-axis reversalY-axis reversalopen/shutY-axis reversalEncoder error correctionopen/shutEncoder error correctionHall error correctionopen/shutHall error correctionRestore settingsYes / noRestore factory settings (but do not restore trim data)
Channel ManualFunction01Function0-25502X-axis0-25503X-axis fine-tuning0-25504Y-axis0-25505Y-axis fine-tuning0-25506XY speed0-25507dimming0-25508stroboscopic0-25509color palette0-25510Fixed diagram disk0-25511Effect pattern0-25512Dynamic diagram disk0-25513Rotating motion diagram0-25514prism0-25515Prism rotation0-25516Atomization&Colorful0-25517magnify0-25518focusing0-25519reset0-25520effect0-255
CalibrationEffectPlease enter a 4-digit password to use this function
DisplayEffectScreen saver time15 seconds /30 seconds /60 seconds / offWhen the time arrives, return to the desktopbacklight time15 seconds /30 seconds /60 seconds / offThe screen will be off when the time reachesScreen reversalOn / offScreen forward and reverse controllanguageChinese / EnglishSelect Chinese or English
ResetEffectreset allYes / noReset all motorsXY resetYes / noXY motor resetHead reductionYes / noHead small motor reset	
Bulb settingffectPower on bright bubbleYes / noAutomatic bubble lighting after power on resetManual light bubbleYes / noManual bubblingHalf powerYes / noWhether half power mode is turned on
DMX data monitoringEffectMonitor DMX512 data value of each channel
Reset informationEffectIf the system reset is normal, the system is normal. If there is a reset error, the corresponding reset error message will be prompted
Sensor informationEffectX encoder*****Current encoder count valueY encoder*****Current encoder count valueX encoder status00/11Encoder a and B signal line statusY encoder status00/11Encoder a and B signal line statusX Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Y Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Color disc Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Pattern disc Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0Focusing Hall0/1Hall state, hall is 1 at magnet position, otherwise it is 0
Usage recordEffectUse times, use time, bright bubble time, etc
System versionEffectSystem hardware version, software version number
Explain：
1. when restoring factory settings, only the underlined parameters in the menu will be restored, and other parameters will not be automatically restored or reset.
【Send local parameters】 menu, you can send the parameter settings of underlined items in the machine to another lamp or multiple lamps through DMX data line to avoid repeated setting work. A reset will be generated when the received lamps receive the correct parameters.
Troubleshooting
ResolventThe lamp is not powered on and has no response at allCheck the fuse for damage
 check whether the AC voltage is normal
Switching power supply inside the lamp body may be damaged
 the internal control board of the lamp body may be damaged
Uncontrolled lamps check whether the DMX signal is normal. When it is normal, the DMX signal indicator on the display board will flash
 check whether the address code is set correctly
 check whether the channel mode is set correctly
Check whether the DMX signal line is too long, or whether there are too many lamps connected in seriesAbnormal movement of XY axisThe optocoupler sensor may be damaged or improperly installed, so that the original correct position can also be corrected. Set it to no in the menu [XY error correction enable] option. Or adjust the optocoupler sensor circuit board to the appropriate position, or replace the circuit board







