EXTRACTED TEXT FROM: 英文老款防水光束灯说明书.doc

USER MANUAL

Waterproof  beam light












Please read this manual carefully before use.




1. Control instructions


Encoder version
Turn clockwise to "down" Function: Select the next item or value plus
Turn counterclockwise to "Up" Function: Select the previous item or the value minus
OK button is "OK" function: OK to save, execute function, start editing, exit editing
Press and hold the OK button for 2 seconds. Exit function: Exit editing Back to previous screen

Button version
The function of the "Back" button is: return to the previous interface to exit the function.
The function of the "Up" key is: select the previous item or the value is extended by 2 seconds.
The function of the "down" button is: select the next item or decrease the value and press 2 seconds to decrement quickly.
The functions of the "OK" button are: OK to save, execute functions, start editing, exit editing
1. Interface description
1.1. Main interface
     Two LEDs on the left Green---(DMX signal indicator) Blue---(Host self-propelled voice control indicator)
3 buttons in the upper right corner for language switching and screen rotation.
The sub-interfaces corresponding to the four buttons in the bottom row are described later.
1.2. Setting interface

OptionDescriptionOperating mode
DMXSlave status: Receive DMX signals from the console or host
Self-propelled
Host status: Run automatically and send DMX signal to slaveNote: If the previous lamp is off, it will not automatically light up. If you need to observe the lighting effect, please light the bulb and then enter the automatic state.Voice control
Host status: voice control operation, and send DMX signal to the slave
Note: If the previous lamp is off, it will not automatically light up.
DMX address
1~512Press the "OK" button to enter the editing state. The "Up" and "Down" keys change the address code. Press "OK" to exit the editing state.Channel mode1616 Channel modeX Reverseturn offopenY Reverseturn offopenXY exchangeturn offopenExchange XY axis channels (including fine tuning)ResetSelect "Yes" to confirm and start the reset.Light bulb controlturn offTurn off the bulbopenTurn on the light bulb (please turn on when the light bulb is cool)Boot bright bubbleturn offReset directly after power-on, do not light the bulb (need to use the menu or console to manually brighten the bulb）openAutomatically brightens after power-on, and resets when the bulb is successfully lit.XY EncoderopenUse encoder (optocoupler) to determine out of step and automatically correct positionturn offCorrect position without encoder (optocoupler)No DMX signal
maintainContinue running as it isClearThe motor returns to the position and stops running.screen protectoropenTurn off the backlight after 30 seconds of idle timeturn offBacklight is always brightColor wheel linearSelect "On" "Off" to enable the off color wheel linear function
Restore default settings
Select "Yes" to confirm and restore the default settings.
1.1. Information interface
OptionDescriptionSoftware versioncurrent software versionTotal usage timeCumulative usage timeCumulative usage time...Usage time since this bootTotal bright timeCumulative brightening time
This bright timeBrightening time since this bootManual control interface
This interface is used to control the current luminaire. It is neither in the slave state (does not receive the DMX signal) nor in the host state (does not send the DMX signal).

OptionDescriptionX0~255Press the "OK" button to enter the editing state. Press the "Up" and "Down" keys to change the channel value. Press the "OK" button again to exit the editing state.……0~255Pattern disk speed0~2551.1. Advanced interfaceThe factory default password is "1010"
OptionDescriptionTime clearBright bubble use time clear. RetimeLight bulb control2-wire 2-wire control lighter No half power Bright bubble detection function5-wire 5-wire control lighterReset calibrationAfter entering the sub-interface, the reset position of the motor such as X-axis and Y-axis can be adjusted to compensate for the error in hardware installation.Note: Do not reset and calibrate while the motor is running! If the motor is running, please let it stop before resetting and calibratingPerform a reset operation before reset calibration if necessaryDMX Channel table


NOChannelDMX Numerical valueFunctional description
CH1colour
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
105
110
115
120
125
130
135
140-199
200-255White light
White light + color 1
Color 1
Color 1 + color 2
Color 2
Color 2+ color 3
Color 3
Color 3+ color 4
Color 4
Color 4+ color 5
Color 5
Color 5+ color 6
Color 6
Color 6+ color 7
Color 7
Color 7+ color 8
Color 8
Color 8+ color 9
Color 9
Color 9+ color 10
Color 10
Color 10+ color 11
Color 11
Color 11+ color 12
Color 12
Color 12+ color 13
Color 13
Color 13+ white light
Rainbow effect is going fast - slow
Rainbow effect reverses slowly - fastCH2Strobe0-2
3-50
51-240
241--255shut down
turn on
Strobe slow--fast
turn onCH3Dimming0-255DarkCH4pattern
0-4
5-9
10-14
15-19
20-24
25-29
30-34
35-39
40-44
45-49
50-54
55-59
60-64
65-69
70-129
130-190
191-195
196-200
201-205
206-210
211-215
216-220
221-225
226-230
231-235
236-240
241-245
246-250
251-255White light
Pattern 1
Pattern 2
Pattern 3
4Pattern
5Pattern 
6Pattern 
7Pattern 
8Pattern 
9Pattern 
10Pattern 
11Pattern 
12Pattern 
13Pattern
Rainbow effect is going fast - slow
Rainbow effect reverses slowly - fast
1 jitterPattern 
2 jitterPattern 
3 jitterPattern
4 jitterPattern 
5 jitterPattern 
6 jitterPattern 
7 jitterPattern 
8 jitterPattern 
9 jitterPattern 
10 jitterPattern 
11 jitterPattern 
12 jitterPattern
13 jitterCH5Prism
0-63
64-127
128-191
192-255no
Insert prism 1
Insert prism 2
Insert prism 1+2
CH6Prism 1 rotation
0-127
128-191
192-255Prism 1 positioning
Fast forward - slow
Reverse slow - fast
CH7NONONOCH8Atomization / colorful
0-127
128-191
192-255no
Atomization
ColorfulCH9focusing0-255Far nearCH10Level0-2550-540°CH12vertical0-2550-270°CH13Vertical fine-tuning0-2550-1.0°CH14XY speed0-255Fast-slowCH15Reset
0-25
26-76
77-127
128-255No function
Small motor reset
Large motor (XY axis) reset
All motor reset
Start reset after staying for 5 secondsCH16Light bulb control
0-9
10-100
101-255No function
Extinguish the bulb
Light bulb
Start switching the bulb after 5 seconds


